Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Ridge Vent Installation: The Enterprise Owner’s Guide
We install CertainTeed-compatible ridge vent systems across Enterprise, and most single-ridge jobs run $420 to $780 installed, including removal of the old vent, deck prep, and new cap shingles. Most jobs are completed in a single visit. You usually find out this part has failed the same way everyone else in Enterprise does: a dark stain blooms on a ceiling near the ridge line, or you climb up after a windy spring day and find a section of vent cap peeled back like a tin can lid. By the time you can see it from the ground, water has often been working at the deck for a season or two.

Which CertainTeed Models This Applies To
CertainTeed makes ridge vent in a few configurations, and which one you have matters for matching the replacement. The most common on Enterprise homes is the 12-inch-wide roll vent, which comes in 20-foot rolls and works with most architectural shingle profiles. The rigid molded version – sometimes called the shingle-over vent – is a different animal, and it’s what you’ll find on newer builds and homes that were re-roofed in the last fifteen years.
Here’s the gotcha most homeowners miss: CertainTeed changed the profile on some of its ridge vent lines over the years, and the old nailing flange pattern doesn’t always line up with the current stock. If your existing vent was installed pre-2010, you can’t assume a direct drop-in. You measure the vent width at the deck, not the cap, and you check the shingle exposure so the new cap shingles blend in. Bring us a photo of the label on the vent roll if there’s one left, and the measurements, and we’ll match it right.
On the OEM-versus-aftermarket question: CertainTeed’s own vent is a good product, but the aftermarket makes compatible profiles that perform the same for less. We install both, and we’ll tell you honestly which makes sense for your roof. We’re an independent service provider, not affiliated with CertainTeed, so our only stake is in the fit. For GAF and Owens Corning roofs, we handle those vent systems too.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Ridge Vent Installation Is Failing
Ridge vent is a quiet part until it isn’t. These are the symptoms we see on Enterprise roofs, and what’s usually behind each one.
- Water staining near the ridge on the ceiling or attic sheathing. The vent’s filter or screen has clogged, or the cap shingles have lifted and water is tracking back under them. Once water gets past the vent, it wicks along the deck and shows up inside.
- Visible gaps, lifting, or curling at the vent cap. Wind has worked the fasteners loose, or the adhesive on the cap shingles has failed. Enterprise gets gusts off the foothills that will find a loose edge and peel it back.
- Attic stays hot and humid no matter what. The vent is clogged with dust and debris, or it was installed with too little net free area for your roof. A vent that can’t breathe traps moisture, which is worse in our dry-then-wet desert swings than people expect.
- Ice dams or frost at the ridge in winter. Warm, moist attic air is escaping where it shouldn’t because the vent isn’t working. That moisture hits the cold ridge and freezes.
- Birds, wasps, or debris in the vent openings. The screen or filter has failed or was never installed. Once the opening is compromised, the vent stops venting and starts collecting.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
On an Enterprise home, a straightforward ridge vent replacement runs $420 to $780. A long ridge, a steep pitch, or a rigid molded vent instead of roll vent pushes toward the top of that range. What drives the number is linear feet of ridge, roof pitch, how much old vent and cap shingle has to come off, and whether the deck underneath needs repair.
Here’s what the price includes: removal of the old vent and cap shingles, inspection of the deck and sheathing, installation of the new vent to the correct net free area for your roof, new cap shingles, and cleanup. The number on the estimate is the number on the invoice. No surprises. The work is backed by our written 90-Day Done Right Promise – if it isn’t right, we come back and make it right, no arguing and no paperwork runaround.
DIY or Call Us?
There’s a safe version of checking this yourself and an unsafe version. Safe: from the ground with binoculars, look for lifted cap shingles or gaps at the ridge. In the attic, look for staining on the sheathing and check whether the vent is clogged with dust or debris. That tells you whether you have a problem.
What we don’t recommend is getting up on the roof to pull the vent yourself. Ridge work puts you at the peak of the roof, on the steepest part, often on shingles that are already compromised – and a fall from a ridge line is the kind of thing that changes a life. If your roof is more than a single story, or the pitch is steep, or the shingles look tired, leave it to us. We’ll send a background-checked, uniformed technician who documents the inspection with photos taken from your actual roof. Call (844) 228-4119 and we’ll get an honest look and a straight price.
FAQs
How long does a CertainTeed ridge vent last in Enterprise? A properly installed ridge vent should last 20 to 30 years, but the cap shingles over it often go first in our climate – the intense UV and the freeze-thaw swings at the ridge age shingles faster than the vent body itself. Inspect the cap shingles every few years. Call (844) 228-4119 for a free roof inspection.
Can it be repaired instead of replaced? Sometimes. If the vent body is sound and only the cap shingles or fasteners have failed, a targeted repair can fix it for a fraction of a full replacement. If the vent is clogged, cracked, or the wrong size for your roof, replacement is the right call. We’ll tell you which one you’re looking at, and the estimate is free.
How long does the swap take? Most single-ridge replacements are done in a single visit, typically a few hours depending on ridge length and pitch. We’ll give you a realistic window when we quote it, and we’ll be there when we say.
How do you source the part? We install CertainTeed and compatible profiles, and we match the vent to your roof’s width, pitch, and shingle exposure before we order. If your existing vent is an older profile, we verify fit against the deck measurements rather than guessing. Call (844) 228-4119 to schedule your free estimate.
Written by the team at Ridgeline Roofing Co. Enterprise, serving Enterprise and nearby areas.