Owens Corning
Architectural shingles
Metal roofing
Tile roofing
GAF
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Owens Corning Flashing Replacement: The Enterprise Owner’s Guide
We replace failed Owens Corning flashing in Enterprise, and most jobs run $320 to $780 installed depending on which flashing type has failed and how much surrounding roofing has to come up with it. Smaller repair-only work (a single pipe boot or a short wall termination) lands near the low end; valley and chimney flashing at the high end. We can often get an inspection and written quote out the same day you call, though the actual replacement is a scheduled job, not a same-day emergency. Most Enterprise owners find out the flashing is gone the same way: a brown water stain spreading across a ceiling near a chimney or skylight, or a roofer’s repair visit that turns into “and the flashing is shot, too.”

Which Owens Corning Models This Applies To
Owens Corning roofing systems aren’t a single product line, and the flashing that works with one won’t necessarily match another. Their shingle lines – Duration, Oakridge, Supreme, Berkshire – all take the same standard metal flashing in most cases, so the shingle model matters less than the flashing type itself. Where Enterprise owners get tripped up is the Duration series’ nail-strip location and the way their layered shingles sit over a step-flash. If you’re replacing step or counter flashing under Duration, the height and bend profile need to match, or you’ll get puckering along the wall. The other gotcha: pipe boots. Owens Corning doesn’t make the pipe boots themselves in every case – they’re sold with the system but often sourced from another manufacturer. Checking the actual boot label (not the shingle wrapper) matters more than assuming it’s Owens Corning-branded.
Identifying the right part is straightforward if you can get on the roof safely. Look for the stamped or printed model info on the boot collar, measure the pipe diameter (standard is 1.5″ to 4″ for residential), and note the shingle line from the wrapper or a leftover bundle. If you don’t have a wrapper, we can usually identify the line from the shingle profile in a photo. On the OEM-vs-aftermarket question: for metal flashing, a quality aftermarket equivalent (proper gauge, correct bend) performs the same as OEM in Enterprise’s heat. For pipe boots and specialty terminations, the OEM or OEM-spec part is worth the few extra dollars because fitment is tighter.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Owens Corning Flashing Replacement Is Failing
- Ceiling stains near a chimney or skylight after rain. Water finds the path of least resistance through the flashing joint, and by the time you see the stain, the underlayment behind it has been wet for a while.
- Visible rust or bubbling on the flashing metal itself. Enterprise’s dry heat and seasonal monsoon moisture cycle metal hard; galvanized flashing that would last 25 years in a wet climate can show bubbling in 12-15 here.
- Curled or lifted shingle edges along the flashing line. The nail heads under the shingle have likely backed out, or the flashing was never properly counter-flashed and the shingle is doing the waterproofing job instead of the metal.
- Cracked pipe boot collars. Rubber collars on pipe boots go first in desert sun. The crack isn’t always visible from the ground, but a hose test on a dry day will expose it fast.
- Water in the attic on the underside of the roof deck near a valley. Valley flashing failure is quiet – no interior stain right away, just dark staining on the wood under the valley line. That’s a costly one if it goes another season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed flashing replacement in Enterprise runs $320 to $780 for most residential jobs. The range is driven by:
- Flashing type: pipe boot ($320-$420), step flashing along a wall ($380-$520), valley flashing ($480-$680), chimney flashing ($520-$780)
- How much roofing gets disturbed: if the flashing replacement requires lifting and re-setting more than a few courses of shingle, add $150-$300
- Number of penetrations: a single boot vs. three boots and a skylight changes the picture quickly
For an Owens Corning system with a specific bend profile or color-matched metal, there may be a small upcharge for the matching part – we tell you up front. The number on the estimate is the number on the invoice, no change orders once we’re on the roof. Work is covered by our written 90-Day Done Right Promise: if it’s not right, we make it right, no paperwork, no arguing. That guarantee covers the workmanship on the flashing install; the part itself carries its own manufacturer coverage.
DIY or Call Us?
Here’s where we’re honest: for a pipe boot with a rubber collar, a careful owner with a ladder and the right size boot can sometimes replace it. For step, valley, or chimney flashing on an Owens Corning system, it’s not a DIY job – not because it’s complicated on paper, but because getting the shingle layers and the counter-flashing right is what separates a 20-year repair from a leak you find next monsoon. The cost of redoing it after a bad DIY repair runs two to three times the original job. For anything involving a chimney, a valley, or lifting shingles on your own roof, call us. Our technicians are background-checked, arrive in uniform, and take photos from your actual roof so you see exactly what’s failing. If you’re not sure whether it’s a DIY job, call and ask – we’ll tell you straight. (844) 228-4119.
FAQs
Metal flashing in Enterprise usually holds 15 to 22 years, while rubber pipe boot collars fail at 8 to 12 years in our sun. That’s the first thing we check on an inspection – the boots are almost always the weak link, not the flashing.
Sometimes – a small crack in a rubber boot can be sealed with flashing cement, and that buys you a season or two. But once the metal is rusted through or the counter-flashing has come loose from the masonry, a repair is a patch on top of a real failure, and replacement is the better call. Call us at (844) 228-4119 for an honest read on which one you’re looking at – estimates are free.
A pipe boot is a 30-to-60 minute job; step or valley flashing typically takes a half day; chimney flashing can run a full day. Most of our jobs are done in a single visit, and we schedule it when it works for you – not around a storm-blasted calendar.
We’re an authorized installer of Owens Corning (also GAF and CertainTeed), so we source the right part through manufacturer channels – not a substituted boot from a big-box shelf. When a job calls for OEM-spec, that’s what goes up. We’re independent and not affiliated with Owens Corning; the distinction matters to some customers, and we want to be clear about it.
Written by the team at Ridgeline Roofing Co. Enterprise, serving Enterprise and nearby areas.
If your Owens Corning flashing has failed, call (844) 228-4119 for a free estimate. Live person answers every call, 24/7. We’ve been standing behind local roofs since 1984, and we will be there when we say.